PT-048
µ TOUGH-8010/STYLUS TOUGH-8010/µ TOUGH-6020/STYLUS TOUGH-6020
µTOUGH-8010/STYLUSTOUGH-8010/µTOUGH-6020/STYLUSTOUGH-6020
µTOUGH-8010/STYLUSTOUGH-8010/µTOUGH-6020/STYLUSTOUGH-6020
µTOUGH-8010/STYLUSTOUGH-8010/µTOUGH-6020/STYLUSTOUGH-6020
µTOUGH-8010/STYLUSTOUGH-8010/µTOUGH-6020/STYLUSTOUGH-6020
µ TOUGH-8010/STYLUS TOUGH-8010/µ TOUGH-6020/STYLUS TOUGH-6020
µTOUGH-8010/STYLUSTOUGH-8010/µTOUGH-6020/STYLUSTOUGH-6020
For safe use
This instruction manual uses various pictographs for correct use of the
product and to prevent danger to the user and other persons as well as
property damage. These pictographs and their meanings are shown
below.
En
This indicates contents for which the possibility of human
death or severe injury in case of handling under
disregard of this indication can be assumed.
WARNING
This indicates contents for which the possibility of human
injury or the possibility of material damage in case of
handling under disregard of this indication can be
CAUTION
assumed.
WARNING
1 Keep this product out of the reach of babies, infants, and children.
There is the possibility of occurrence of the following types of
accidents.
• Injury by dropping onto the body from a height.
• Injury from parts of the body getting caught in parts which open and
close.
• Swallowing of small parts, O-ring, silicone grease and silica gel.
Please consult a physician immediately if any parts have been
swallowed.
• Triggering of the flash in front of the eyes may cause permanent
vision impairment etc.
2 Do not store with a battery in the digital camera housed in this product.
Storage with a battery inserted may lead to leakage of the battery
liquid and fire.
3 If leakage of water should occur with a camera installed in this product,
quickly remove the battery from the camera. There is the possibility of
ignition and explosion from generation of hydrogen gas.
4 This product is made of resin. There is the possibility that injuries may
be caused when it becomes broken because of strong impact with a
rock or other hard objects. Please handle it with sufficient care.
EN 3
CAUTION
1 Do not disassemble or modify this product. This may cause water
leakage or trouble. OLYMPUS IMAGING CORP. shall not be
responsible for damage, lost profits, etc. caused by loss of image data
because of disassembly, repair or modification of this product by
people other than third parties specified by OLYMPUS IMAGING
CORP. or for other reasons.
En
2 Use or storage of the product at the following locations may cause
defective operation, trouble, damage, fire, internal clouding, or water
leakage. This should be avoided.
• Locations reaching high temperatures such as those under direct
sunlight, in an automobile, etc.
• Locations with open fire
• Water depths in excess of 40 m
• Locations subject to vibrations
• Locations with high temperature and humidity or with severe
temperature changes
• Locations with volatile substances
3 Opening and closing at locations with much sand, dust, or dirt may
impair the waterproof characteristic and cause water leakage. This
should be avoided.
4 This product is not a case to soften impacts to the camera inside the
product. When this product with a digital camera inside it is subjected
to impacts or heavy objects are placed onto it, the digital camera may
become damaged. Please handle it with sufficient care.
5 Do not use the following chemicals for cleaning, corrosion prevention,
prevention of fogging, repair or other purposes. When these are used
for the Case directly or indirectly (with the chemicals in vaporized
state), they may cause cracking under high pressure or other
problems.
EN 4
Chemicals which cannot
be used
Explanation
Volatile organic solvents, Do not clean the Case with alcohol, gasoline,
chemical detergents
thinner or other volatile organic solvents or with
chemical detergents etc. Use pure water or
lukewarm water.
En
Anticorrosion agent
Do not use anticorrosion agents. The metal parts
use stainless steel or brass. Wash with pure
water.
Commercial defogging
agents
Do not use commercial defogging agents. Always
use the specified desiccant silica gel.
Grease other than
Use only the specified silicone grease for the
specified silicone grease silicone O-ring, as otherwise the O-ring surface
may deteriorate and water leakage may occur.
Adhesive
Do not use adhesive for repairs or other purposes.
When repair is required, please contact a dealer or
a service station of OLYMPUS IMAGING CORP.
6 Jumping into the water with the Case in your pocket or in your hand,
throwing the Case from a boat or ship into the water, and other rough
handling may cause water leakage. Please handle with sufficient care,
when handing it over from hand to hand etc.
7 If the camera on the inside should become wet because of water
leakage etc., immediately wipe off all moisture and confirm the
operation after the Case is dried.
8 Please remove the O-ring when traveling by air. Otherwise air
pressure may make it impossible to open the Case.
9 For safe use of the digital camera in this product, please read the
“Instruction Manual” for the digital camera carefully.
0 When sealing this product, take sufficient care that no foreign matter
gets caught at the O-ring and the contact surface. It is caused for water
leakage.
a When you install your digital camera in the Case after taking pictures
in the water, it may cause the loss of transparency of the lens inside
even if you insert the supplied silica gel to the Case when drying the
camera is insufficient.
EN 5
Contents
Introduction ........................................................................... 2
Please read the following items before use .......................... 2
For safe use .......................................................................... 3
En
1. Preparations.................................................................... 8
Check the contents of the package....................................... 8
Names of the parts................................................................ 9
Using the accesories........................................................... 11
Install the strap.................................................................... 11
Installation and removal of the LCD hood ........................... 12
Mounting and removing the lens cap .................................. 12
Using the fiber cable adapter .............................................. 13
2. Advance Check of the Case.......................................... 14
Advance check before use.................................................. 14
3. Install the digital camera................................................ 15
Check the digital camera..................................................... 15
Open the Case.................................................................... 16
Load the digital camera....................................................... 17
Make sure the camera is loaded properly........................... 17
Seal the Case...................................................................... 18
Check the operation of the loaded camera ......................... 18
Perform the final checks...................................................... 19
Visual Inspection ................................................................. 19
Water Leakage Test............................................................ 19
4. Taking Pictures Under Water ........................................ 20
Underwater shooting modes ............................................... 20
How to select the shooting scene ....................................... 21
Locking AF during underwater shooting.............................. 21
5. Handling After Shooting ................................................ 22
Wipe off any waterdrop ....................................................... 22
Take out the digital camera................................................. 23
Wash the Case with pure water .......................................... 23
Dry the Case ....................................................................... 23
6. Maintaining the Waterproof Function ............................ 24
Remove the O-ring.............................................................. 24
Remove any sand, dirt, etc. ................................................ 24
EN 6
How to Apply Grease to the O-ring......................................26
Install the O-ring...................................................................27
Replace consumable parts ..................................................27
7. Appendix........................................................................28
Specifications.......................................................................28
En
EN 7
1. Preparations
Check the contents of the package.
En
Check that all accessories are in the box.
Contact your dealer if accessories are missing or damaged.
• LCD hood
• Silicone grease
(on the body)
• Optical
fiber cable
adapter
• LCD hood
strap
• Silica gel (1g)
• Lens cap
• Hand strap
• Case body
(Check that the O-ring is installed)
• O-ring remover
• Adapter
Black (PTAC-07)
White (PTAC-06)
• Instruction manual (this manual)
• OLYMPUS distributor list
EN 8
Names of the parts
4
3
5
En
2
1
6
7
8
9
0
a
b
1 Palm grip
2 Diffuser
5 Accessory mount
6 Front lid
9 LCD inner hood
0 O-ring
*3 Shutter lever
*4 ON/OFF button
7 Open/close dial
8 Lens ring
a Tripod seat
b Light shield hood
EN 9
c
d
e
f
g
En
h
i
m
l k
j
*c Arrow pad W
*d ( (REC) button
*e Zoom buttons
*f q button
*i OK/AFL button (*1)
*j E button
(*1) During Underwater Wide-
Angle 1 or Underwater Macro
shooting mode, the OK button
k
button/arrow pad T
l MENU button
m LCD monitor window
*g INFO button/arrow pad S functions as the AF LOCK
*h Arrow pad X
button.
Memo:
The Case operation parts marked by * corresponds to the operation parts of
the digital camera. When the operation parts of the Case are operated, the
corresponding functions of the digital camera will operate. For details of the
functions, refer to the instruction manual for the digital camera.
EN 10
Using the accesories
Install the strap
Install the strap on the Case body.
Installation illustration
En
Installation completed
Hand strap
Hand strap ring
How to use the hand strap
Pass your hand through the hand strap and adjust the length with the stop
button.
stop button
EN 11
Installation and removal of the LCD hood
Installation
Strongly push the LCD hood as shown in the figure into the rails above
and below the LCD monitor window.
En
Removal
Remove the LCD hood from the rails above and below the LCD monitor
window by widening the LCD hood.
Guides
Installation
Removal
Mounting and removing the lens cap
Fit the lens cap onto the lens ring as
shown in the figure. Be sure to
remove the lens cap before
shooting.
EN 12
|